Mylinking™ Network Tap ML-TAP-2610
24*GE SFP plus 2*10GE SFP+, Max 44Gbps
1- Overviews
- A full visibility control of network traffic collection device(2*10GE SFP+ plus 24*GE SFP ports)
- A full Data Scheduling Management device(duplex Rx/Tx processing)
- A full pre-processing and re-distribution device(bidirectional bandwidth 44Gbps)
- Supported collection & reception of link data from different network element locations
- Supported collection & reception of link data from different switch routing nodes
- Supported raw packet collected, identified, analyzed, statistically summarized and marked
- Supports LAN/WAN mode; Supports packet filtering and forwarding based on the source port, quintuple standard protocol domain, source/destination MAC address, IP fragment, transport layer port range, Ethernet type field, VLANID, MPLS label, and TCPFlag fixed offset feature.
- Supported port traffic aggregation, Hash diversion, load balancing, and filtering, flexibly meeting your network security and traffic analysis device deployment requirements.
- Supported automatically various tunneling protocols identification such as GTP / GRE / PPTP / L2TP / PPPOE. Regarding the user configuration, the traffic output strategy can be implemented according to the inner or outer layer of the tunnel
ML-TAP-2610
2- System Block Diagram
Mylinking™ ML-TAP-2610 Network Tap is ASIC dedicated chip pure hardware design, high-speed backplane switching bus bandwidth up to 44Gbps, can achieve complete line speed flow collection, convergence, filtering, shunt, replication and other functions; TCAM hardware policy matching mark engine module can complete the packet security policy matching and traffic classification mark under the state of line speed flow. The traffic steering engine can implement free port forwarding, replication and shunting actions of marked traffic.
3- Operating Principle
- The easy-to-use WEB configuration interface eliminates complex CLI configuration. Advanced users can use no more than five commands to configure the complex traffic replication in different ports.
- Status monitoring; Port status on the WEB UI displays the power supply, system status, interface rate, interface LINK status, and data packets sent and received by the port.
- Fully compatible with intrusion detection system, protocol analyzer, RMON probe, network audit system and other applications.
4- Intelligent Traffic Processing Abilities
ASIC Chip Plus TCAM CPU
44Gbps intelligent traffic processing capabilities
10GE Traffic Acquisition
10GE 2 ports, Max 2*10GE plus 24*GE ports Rx/Tx duplex processing, up to 44Gbps Traffic Data Transceiver at same time, for network Data Capture, and simple Pre-processing
Data Replication
Packet replicated from 1 port to multiple N ports, or multiple N ports aggregated, then replicated to multiple M ports
Data Aggregation
Packet replicated from 1 port to multiple N ports, or multiple N ports aggregated, then replicated to multiple M ports
Data Distribution
Classified the incoming data accurately and discarded or forwarded different data services to multiple interface outputs according to user’s predefined rules.
Data Filtering
Supported network L2-L7 packet filtering matching, such as SMAC, DMAC, SIP, DIP, Sport, Dport, TTL, SYN, ACK, FIN, Ethernet type field and value, IP protocol number, TOS, etc. also supported flexible combination of up to 2000 filtering rules.
Load Balancing
Supported load balance Hash algorithm and session-based weight sharing algorithm according to L2-L7 layer characteristics to ensure that the port output traffic dynamic of load balancing
UDF Match
Supported the matching of any key field in the first 128 bytes of a packet. Customized the Offset Value and Key Field Length and Content, and determining the traffic output policy according to the user configuration
VLAN Tagged
VLAN Untagged
VLAN Replaced
Supported the matching of any key field in the first 128 bytes of a packet. The user can customize the offset value and key field length and content, and determine the traffic output policy according to the user configuration.
MAC Address Replacement
Supported the replacement of the destination MAC address in the original data packet, which can be implemented based on the user's configuration
3G/4G Mobile Protocol Recognition/Classification
Supported to identify mobile network elements such as (Gb, Gn, IuPS, S1-MME, S1-U, X2-U, S3, S4, S5, S6a, S11, etc. interface). You can implement traffic output policies based on features such as GTPV1-C, GTPV1-U, GTPV2-C, SCTP, and S1-AP based on user configurations.
Ports Healthy Detection
Supported the real time detection of the service process health of the back-end monitoring and analysis equipment connected to different output ports. When the service process fails, the faulty device is automatically removed. After the faulty device is recovered, the system automatically returns to the load balancing group to ensure the reliability of multi-port load balancing.
VLAN, MPLS Untagged
Supported the VLAN, MPLS header stripping in the original data packet, and output.
Tunneling Protocol Identify
Supported automatically identify various tunneling protocols such as GTP / GRE / PPTP / L2TP / PPPOE. According to the user configuration, the traffic output strategy can be implemented according to the inner or outer layer of the tunnel
Unified Control Platform
Supported mylinking™ Visibility Control Platform Access
1+1 Redundant Power System(RPS)
Supported 1+1 Dual Redundant Power System
5- Mylinking™ Network Tap Typical Application Structures
5.1 Mylinking™ Network Tap GE to 10GE Data Aggregation Application(as following)
5.2 Mylinking™ Network Tap 1/10GE Data Distribution Application(as following)
5.3 Mylinking™ Network Tap Hybrid Acquisition Application (as following)
5.4 Mylinking™ Network Tap Customazition Traffic Monitoring Application(as following)
6- Specifications
|
Mylinking™ Network Tap NPB/TAP Functional Parameters |
||
|
Network Interface |
GE ports |
24*GE SFP slots |
| 10GE ports |
2*10GE SFP+ slots |
|
|
Deployment mode |
SPAN monitoring input |
support |
| In-line mode |
support |
|
| Total QTYs interface |
26 |
|
| Traffic replication / aggregation / distribution |
support |
|
| Link QTYs supporting Mirror replication / aggregation |
1 -> N link traffic replication (N <26) |
|
|
N-> 1 link traffic aggregation (N <26) |
||
|
G Group(M-> N Link) traffic replication and aggregation [G * (M + N) <26] |
||
|
Functions |
Distribution based on traffic identification |
support |
| Distribution based on IP / protocol / port Five tuple traffic identification |
support |
|
| Distribution strategy based on protocol header the key labeled traffic identifies |
support |
|
| Strategic distribution based on deep message content identification |
support |
|
| Support Ethernet encapsulation independence |
support |
|
| CONSOLE Network Management |
support |
|
| IP/WEB Network Management |
support |
|
| SNMP V1/V2C Network Management |
support |
|
| TELNET/SSH Network Management |
support |
|
| SYSLOG Protocol |
support |
|
| User authentication function | Password authentication based on user name | |
|
Electric(1+1 Redundant Power System-RPS) |
Rated supply voltage |
AC110-240V/DC-48V [Optional] |
| Rated power frequency |
AC-50HZ |
|
| Rated input current |
AC-3A / DC-10A |
|
| Rated power function |
150W(2401: 100W ) |
|
|
Environment |
Operating Temperature |
0－50℃ |
| Storage Temperature |
-20-70℃ |
|
| Operating Humidity |
10%-95%, Non-condensing |
|
|
User Configuration |
Console Configuration |
RS232 Interface, 9600,8,N,1 |
| Password authentication |
support |
|
|
Rack Height |
Rack space (U) |
1U 460mm*45mm*440mm |
7- Order Information
ML-TAP-2401 mylinking™ Network Tap 24*GE SFP ports
ML-TAP-1410 mylinking™ Network Tap 12*GE SFP ports plus 2*10GE SFP+ ports
ML-TAP-2610 mylinking™ Network Tap 24*GE SFP ports plus 2*10GE SFP+ ports
ML-TAP-2810 mylinking™ Network Tap 24*GE SFP ports plus 4*10GE SFP+ ports
